Thermal performance testing of heat exchangers with reference to future automation

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY WITH PRIOR ARRANGEMENT

The automation of resonant thermometer probe measurements

An ultrasonic thermometer has been developed for high temperature measurement over a wide temperature range. It is particularly suitable for use in measuring nuclear fuel rod centerline temperatures in advanced liquid metal and high flux nuclear reactors. The thermometer which was designed to determine fuel temperature up to the fuel melting point, utilizes the temperature dependence of the ultrasonic propagation velocity (related to the elastic modulus} in a thin rod sensor as the temperature transducing mechanism. A pulse excitation technique has been used, where the mechanical resonator at the remote end of the acoustic·line is madto vibrate. Its natural frequency is proportional to the ultrasonic velocity in the material. This is measured by the electronic instrumentation and enables a frequency­ temperature or period-temperature calibration to be obtained. A completely digital automatic instrument has been designed, constructed and tested to track the resonance frequency of the temperature sensors. It operates smoothly over a frequency range of about 30%, more than the maximum working range of most probe materials. The control uses the basic property of a resonator that the stored energy decays exponentially at the natural frequency of the resonator.The operation of the electronic system is based on a digital multichannel transmitter that is capable of operating with a predefined number of cycles in the burst. this overcomes a basic defect in the previous deslgn where the analogue time-delayed circuits failed to hold synchronization and hence automatic control could be lost. Development of a particular type of temperature probe, that is small enough to fit into a standard 2 mm reactor tube has made the ultrasonic thermometer a practicable device for measuring fuel temperature. The bulkiness of previous probes has been overcome, the new design consists of a tuning fork, integral with a 1mm line, while maintaining a frequency of no more than 100 kHz. A magnetostrictive rod, acoustically matched to the probe is used to launch and receive the acoustic oscillations. This requires a magnetic bias and the previously used bulky magnets have been replaced by a direct current coil. The probe is supported by terminating the launcher with a short heavy isolating rod which can be secured to the reactor structure. This support, the bias and launching coil and the launcher are made up into a single compact unit. On the material side an extensive study of a wide range of refractory materials identified molybdenum, iridium, rhenium and tungsten as satisfactory for a number of applications but mostly exhibiting to some degree a calibration drift with thermal cycling. When attention was directed to ceramic materials, Sapphire (single crystal alumina) was found to have numerous advantages, particularly in respect of stability of calibration which remained with ±2°C after many cycles to 1800oC. Tungsten and thoriated tungsten (W - 2% Tho2) were also found to be quite satisfactory to 1600oC, the specification for a Euratom application.

Business implications of manufacturing innovation : the experience of increasing automation in smaller to medium sized companies.

Despite the considerable potential of advanced manufacturing technologies (AMT) for improving the economic performance of many firms, a growing body of literature highlights many instances where realising this potential has proven to be a more difficult task than initially envisaged. Focussing upon the implementation of new manufacturing technologies in several smaller to medium sized enterprises (SME), the research examines the proposition that many of these problems can be attributed in part to inadequate consideration of the integrated nature of such technologies, where the effects of their implementation are not localised, but are felt throughout a business. The criteria for the economic evaluation of such technologies are seen as needing to reflect this, and the research develops an innovative methodology employing micro-computer based spreadsheets, to demonstrate how a series of financial models can be used to quantify the effects of new investments upon overall company performance. Case studies include: the development of a prototype machine based absorption costing system to assist in the evaluation of CNC machine tool purchases in a press making company; the economics and strategy of introducing a flexible manufacturing system for the production of ballscrews; and analysing the progressive introduction of computer based printing presses in a packaging and general print company. Complementary insights are also provided from discussion with the management of several other companies which have experienced technological change. The research was conducted as a collaborative CASE project in the Interdisciplinary Higher Degrees Scheme and was jointly funded by the SERC and Gaydon Technology Limited and later assisted by PE-Inbucon. The findings of the research shows that the introduction of new manufacturing technologies usually requires a fundamental rethink of the existing practices of a business. In particular, its implementation is seen as ideally needing to take place as part of a longer term business and manufacturing strategy, but that short term commercial pressures and limited resources often mean that firms experience difficulty in realising this. The use of a spreadsheet based methodology is shown to be of considerable assistance in evaluating new investments, and is seen as being the limit of sophistication that a smaller business is willing to employ. Several points for effective modelling practice are also given, together with an outline of the context in which a modelling approach is most applicable.

Computer automation of land evaluation procedures

This study was concerned with the computer automation of land evaluation. This is a broad subject with many issues to be resolved, so the study concentrated on three key problems: knowledge based programming; the integration of spatial information from remote sensing and other sources; and the inclusion of socio-economic information into the land evaluation analysis. Land evaluation and land use planning were considered in the context of overseas projects in the developing world. Knowledge based systems were found to provide significant advantages over conventional programming techniques for some aspects of the land evaluation process. Declarative languages, in particular Prolog, were ideally suited to integration of social information which changes with every situation. Rule-based expert system shells were also found to be suitable for this role, including knowledge acquisition at the interview stage. All the expert system shells examined suffered from very limited constraints to problem size, but new products now overcome this. Inductive expert system shells were useful as a guide to knowledge gaps and possible relationships, but the number of examples required was unrealistic for typical land use planning situations. The accuracy of classified satellite imagery was significantly enhanced by integrating spatial information on soil distribution for Thailand data. Estimates of the rice producing area were substantially improved (30% change in area) by the addition of soil information. Image processing work on Mozambique showed that satellite remote sensing was a useful tool in stratifying vegetation cover at provincial level to identify key development areas, but its full utility could not be realised on typical planning projects, without treatment as part of a complete spatial information system.

Automation, rationalisation and concentration : a case study in the British chemical industry

This thesis is based upon a case study of the adoption of digital, electronic, microprocessor-based control systems by Albright & Wilson Limited - a UK chemical producer. It offers an explanation of the company's changing technology policy between 1978 and 1981, by examining its past development, internal features and industrial environment. Part One of the thesis gives an industry-level analysis which relates the development of process control technology to changes in the economic requirements of production . The rapid diffusion of microcomputers and other microelectronic equipment in the chemical industry is found to be a response to general need to raise the efficiency of all processes, imposed by the economic recession following 1973. Part Two examines the impaot of these technical and eoonomic ohanges upon Albright & Wilson Limited. The company's slowness in adopting new control technology is explained by its long history in which trends are identified whlich produced theconservatism of the 1970s. By contrast, a study of Tenneco Incorporated, a much more successful adoptor of automating technology, is offered with an analysis of the new technology policy of adoption of such equipment which it imposed upon Albright & Wilson, following the latter's takeover by Tenneco in 1978. Some indications of the consequences by this new policy of widespread adoptions of microprocessor-based control equipment are derived from a study of the first Albright & Wilson plant to use such equipment. The thesis concludes that companies which fail to adopt rapidly the new control technology may not survive in the recessionary environment, the long- established British companies may lack the flexibility to make such necessary changes and that multi-national companies may have an important role jn the planned transfer and adoption of new production technology through their subsidiaries in the UK.

Manufacturing and assembly automation by integrated metrology systems for aircraft wing fabrication

Discrepancies of materials, tools, and factory environments, as well as human intervention, make variation an integral part of the manufacturing process of any component. In particular, the assembly of large volume, aerospace parts is an area where significant levels of form and dimensional variation are encountered. Corrective actions can usually be taken to reduce the defects, when the sources and levels of variation are known. For the unknown dimensional and form variations, a tolerancing strategy is typically put in place in order to minimize the effects of production inconsistencies related to geometric dimensions. This generates a challenging problem for the automation of the corresponding manufacturing and assembly processes. Metrology is becoming a major contributor to being able to predict, in real time, the automated assembly problems related to the dimensional variation of parts and assemblies. This is done by continuously measuring dimensions and coordinate points, focusing on the product's key characteristics. In this paper, a number of metrology focused activities for large-volume aerospace products, including their implementation and application in the automation of manufacturing and assembly processes, are reviewed. This is done by using a case study approach within the assembly of large-volume aircraft wing structures.

A three-level RFID-based automation approach to enhance network competitiveness

Today, the question of how to successfully reduce supply chain costs whilst increasing customer satisfaction continues to be the focus of many firms. It is noted in the literature that supply chain automation can increase flexibility whilst reducing inefficiencies. However, in the dynamic and process driven environment of distribution, there is the absence of a cohesive automation approach to guide companies in improving network competitiveness. This paper aims to address the gap in the literature by developing a three-level framework automation application approach with the assistance of radio frequency identification (RFID) technology and returnable transport equipment (RTE). The first level considers the automation of data retrieval and highlights the benefits of RFID. The second level consists of automating distribution processes such as unloading and assembling orders. As the labour is reduced with the introduction of RFID enabled robots, the balance between automation and labour is discussed. Finally, the third level is an analysis of the decision-making process at network points and the application of cognitive automation to objects. A distribution network scenario is formed and used to illustrate network reconfiguration at each level. The research pinpoints that RFID enabled RTE offers a viable tool to assist supply chain automation. Further research is proposed in particular, the area of cognitive automation to aide with decision-making.

The automation of protein crystal presentation for x ray diffraction experiments using standing acoustic waves in a microfluidic chip environment

As the pressure continues to grow on Diamond and the world's synchrotrons for higher throughput of diffraction experiments, new and novel techniques are required for presenting micron dimension crystals to the X ray beam. Currently this task is both labour intensive and primarily a serial process. Diffraction measurements typically take milliseconds but sample preparation and presentation can reduce throughput down to 4 measurements an hour. With beamline waiting times as long as two years it is of key importance for researchers to capitalize on available beam time, generating as much data as possible. Other approaches detailed in the literature [1] [2] [3] are very much skewed towards automating, with robotics, the actions of a human protocols. The work detailed here is the development and discussion of a bottom up approach relying on SSAW self assembly, including material selection, microfluidic integration and tuning of the acoustic cavity to order the protein crystals.

The automation of protein crystal presentation for X ray diffraction experiments using standing acoustic waves in a microfluidic chip environment

As the pressure continues to grow on Diamond and the world's synchrotrons for higher throughput of diffraction experiments, new and novel techniques are required for presenting micron dimension crystals to the X ray beam. Currently this task is both labour intensive and primarily a serial process. Diffraction measurements typically take milliseconds but sample preparation and presentation can reduce throughput down to 4 measurements an hour. With beamline waiting times as long as two years it is of key importance for researchers to capitalize on available beam time, generating as much data as possible. Other approaches detailed in the literature [1] [2] [3] are very much skewed towards automating, with robotics, the actions of a human protocols. The work detailed here is the development and discussion of a bottom up approach relying on SSAW self assembly, including material selection, microfluidic integration and tuning of the acoustic cavity to order the protein crystals.